impact strength

High impact strength even at low temperatures.

在低温下也能承受高冲击强度.

The results show that better combination of low temperature impact toughness, fracture toughness and tensile strength can be obtained by quenching at between 860 ° C and 920 ° C and tempering at from 550 ° C to 600 ° C.

实验结果表明，淬火温度为860～920°C，回火温度为550～600°C时，该钢的低温冲击韧性、断裂韧性和抗拉强度可获良好的匹配。

Study on resisted impact strength test procedures of carbon graphite products

炭石墨制品抗冲击强度试验方法的研究

Results The impact strength had relations with the packing time of acrylic;

结果试件抗冲击强度的大小与填塞期的选择有关；

The impact strength of their composites increases obviously and, being toughened with PSF, by a factor of 90 %.

其复合材料的冲击强度明显提高, 经聚砜增韧后提高了90%.

The impact strength of modified resin was increased effectively.

其中不饱和脂肪酸有效地提高了树脂的抗冲击强度.

Analysis on factors affecting impact strength of bulk polystyrene resin

本体聚苯乙烯树脂冲击强度影响因素分析

Impact strength first decreases gradually, and come to constant value as the testing temperature pass a critical value ( T b or T g);

S1随C1的减小而增大。（2）冲击强度先逐渐下降，然后保持恒值；

The tensile strength, impact strength, flexural strength, thermal properties and morphology of the composites were investigated.

研究了复合材料的拉伸强度 、 冲击强度 、 弯曲强度 、 形态及热性能.

This will not only affect the impact strength, to food and health standards.

这不但感化不简单强度, 感化到食物韵味和卫生尺度.

A New Metal Material Impact Strength Measurement Digital Instrument

一种新型的金属材料冲击韧性数字测量仪

Improved heat distortion temperature and low ; temperature impact strength.

提高热变型温度和低温冲击强度.

Impact strength 50 kg · cm;

冲击强度50kg·cm；

Design of measurement and control system of an intelligent plastic impact strength tester

智能化塑料冲击韧性试验机测控系统设计

The greater the viscosity ratio, the higher the impact strength.

粘度比越大，冲击强度相对较高；

Influence Factory of Impact Strength for Copper Infiltrated Sintering Steel

影响渗铜烧结钢冲击强度的因素

The Izod impact strength, the bending strength and tensile strength were tested.

同时,测试了该材料的冲击强度 、 弯曲强度和拉伸强度.

So the ACR is an effective modifier for improving impact strength of PVC.

因此所合成的ACR是 一种有效的PVC抗冲改性剂.

The introduction of graded coarse and fine aggregate, and analyze its impact strength, thermal conductivity, slump, determine a variety of materials suitable for practical application of the grading scale.

引入级配来处理粗细骨料，并分析其对强度、导热系数、坍落度等的影响，确定各种材料最适宜实际应用的级配、比例。

For testing the impact strength of gypsum board.

主要用于石膏装饰板抗冲击强度的测定.

Elastomer-modified injection molding grade for applications requiring highest impact strength together with low stiffness.

注塑级,改性级,最高抗冲击强度,低硬度.宜制工程件.

Preparation of Glass Fiber Reinforced Nylon 66 with High Impact Strength

高抗冲玻纤增强尼龙-66的研制

The testing results indicate that nanosized particles are uniformly located within bulk nanoplastics, and laser powers can strongly affect the HRL and notch impact strength of nanoplastics.

试验结果表明，纳米粒子均匀地分散在纳米塑料中，激光功率对纳米塑料的洛氏硬度及缺口抗冲击强度有显著影响。

The little carbon nanotube can improve impact strength, antistativity and electric conductivity of UHMWPE.

用少量的碳纳米管就能改善UHMWPE的抗冲击 、 抗静电及导电性能.

The tensile and impact strength of the composites were measured.

测定了复合材料的拉伸强度和冲击强度；

With high ductility and impact strength . E . g . Automotive safety parts.

高延展性及良好的冲击强度.

Study on Influencing Factors of Notched Impact Strength of PC/ ABS Blends System

PC/ABS共混体系缺口冲击强度影响因素的研究

Effects of dosages of ABS on the impact strength of rigid PVC were studied.

研究了ABS用量变化对改性硬质聚氯乙烯体系冲击性能的影响.

How is the impact strength related to static strength?

冲击强度和静强度是什么关系?

Added powder filler and short glass fibres can improve the impact strength and loss factor obviously.

一种粉状填料和短切玻纤的加入可显著提高PU结构 泡沫的损耗因子和冲击强度值.